Perform a 'rinse' using a cloth dampened (not dripping) with warm water to wipe the exterior of the carrying case.
Ensure you remove all visible soil a damp, soft-bristled brush may be used if necessary.Ĥ. Use a cloth dampened (not dripping) with a mild, household liquid Dish washing solution to clean the exterior of the carrying case. Use a dry, soft-bristled brush gently to remove any visible soil on the carrying case before wiping.ģ. Remove the SimplyGo device from the carrying case.Ģ.
The carrying case should be cleaned monthly by performing the following steps:ġ. To wash the carrying case, use only warm water and a mild liquid dish detergent. If necessary, the carrying case can be washed using a mild laundry detergent. If using a humidifier, clean it according to home care provider's or manufacturer's instructions.įollow the instructions below when cleaning the accessories. Clean the device exterior using a damp cloth with a mild household cleaner and wipe it dry. The exterior covers of the device and rechargeable battery should be cleaned as needed. Patient Maintenance What is patient maintenance is required with the SimplyGo? The Power Connection symbol disappears when the device is disconnected from the power source. This symbol appears when the device is connected to an AC, DC, or airline power source. This battery symbol appears when the battery is fully charged. The left side of the symbol indicates charging, and the right side indicates the battery level. When a battery symbol similar to this appears (with the charging bars scrolling on the left and mid-height on the right), the battery is partly full and recharging. This battery symbol appears (while the charging bars scrolling on the left side) when the battery is almost depleted and recharging.īattery Charging While Partly Full Symbol If the alarm continues, contact your home care provider.īattery Charging While Almost Empty Symbol See the SimplyGo Carrying Case section of this manual.Īllow the device to warm up. The vents should be visible through the slot at the bottom. If the device is operating in the carrying case, make sure it has been placed correctly in the case so that the outlet vents are in the front. This symbol appears when corrective action is required. This symbol appears when you have pressed that alarm silence button on the control panel to silence an audible alarm. Refer to the associate alarm indicator also being displayed. This symbol appears when an event occurs that generates an audible alarm. This alarm can be silenced by pressing the alarm symbol. This alarm occurs when approximately two minutes of battery life remains. This alarm occurs when the device detects there is no oxygen flowing in the patient cannula.Ĭheck the cannula for kinks or other obstructions that are stopping oxygen flow through it.Ī sequence of alternating short and long beeps that repeats every 4 seconds Replace the battery or connect to a power source.Ī sequence of 3 short beeps + 1 long beep that repeats every 4 seconds Note: This alarm could take up to 45 seconds to activate from the time the alarm condition is present. This alarm can be silenced by pressing the Alarm symbol. Remaining battery life is dependent on your device settings and your activity level. The empty battery symbol flashes on-screen This alarm occurs when approximately 15 minutes of battery life remains. Note: The amount of time it can take for the alarm to activate from the time the alarm condition is present will vary depending of the technical fault that occurs.Ĭhange to another source of oxygen and contact your home care provider.ġ short beep that repeats every 4 seconds This alarm can be silence if the bell symbol appears on-screen. The device many or many not shut down depending on the severity of the alarm. This alarm occurs when the device has general malfunction and the device is no longer operating properly. If this indicator regularly occurs, contact your home care provider.Ī sequence of 3 short beeps + 3 long beeps that repeats every 4 seconds The indicator resets itself when the breath rate is reduced. Note: This alarm could take up to 2 minutes to activate from the time the alarm condition is present. The device is still working properly and is still providing oxygen at the max 2 LPM capacity of the device. This alarm indicates that the user's breath rate is exceeding the capacity of the device. What is the noise level of SimplyGo? 84%ᵒ².Ĭhange to another source of oxygen and contact your equipment provider What is the size of the SimplyGo? 11.4 in x 10 in x 6 in (29.2 cm x 25.4 cm x 15.2 cm) How much does the SimplyGo weigh? 10 lbs.
0 kommentar(er)
